Looking for:
Wintherm software free download |
Sunday, January 22, 2023
Wintherm software free download.Downloads | ThermoAnalytics
Wintherm software free download - Related Articles
The time saved is however enormous. The overview must be first opened before all further actions are executed. Normal reading. Starts normal reading of the recorded data. Further operation of acquisition tasks or the Wintherm programmer mode in conjunction with slight temporal restrictions is still possible in the background.
Fast reading. Starts fast reading of the recorded data. Acquisition tasks running in the background or the Wintherm programmer mode are stopped while reading is taking place. It is not possible to cancel the read-in process. The time saved is enormous. Saves the read-in data in a measurement file, compatible with other measurement files generated by the system. Show graphics. If the data have already been saved, the associated diagram is displayed. If the data have not yet been saved, a request is made to save the data.
Change date. Proline supplies the day of the month and the time at which the last recording was started. Ramps, temperature step changes or also temperature retention phases for the same start and end temperatures in the segment are possible.
On starting, the current setpoint is taken as the starting value of the first segment. Under Create or edit segments you can manage segment tables. Under Read segments information about single or all segments can be read from a device.
Wintherm supports two programmer operating modes: the programmer function if present integrated in the device an internal Wintherm programmer for use with all devices. The segment tables are each saved in the device and are also retained after switching off. The segment tables can be entered into the device manually or transferred to the device by Wintherm.
Vice versa, existing segment tables can be read out and saved as files except that segment tables cannot be read out with P-controllers. Device series Ecoline E Ecoline E Ecoline E Star Edition Ecoline E Star Edition Program internal Available segments Maximum duration of a segment minutes Quantities in the segment table Starting values 16 h min ECO 16 h min h min temperature, duration temperature, duration temperature, duration temperature, duration, tolerance, pump level temperature, tolerance, pump level For use with Wintherm programmer yes, pump level maximum 5 yes, pump level maximum 5 yes, pump level maximum 5 yes, pump level maximum 5 yes, pump level maximum 8 26 Wintherm Plus.
Proline also uses starting values for the tolerance and pump level. These values are saved in the device.
Other devices do not use any starting value so that the required starting setpoint should be specified for the device at the start of the programmer mode in order to start from a defined initial point Wintherm programmer Apart from the programmer functions integrated in the device, Wintherm also contains an internal programmer function, which can be used for devices without an internal programmer or as an alternative to the programmer. Whereas the device programmer runs autonomously, the internal Wintherm programmer can only be executed when Wintherm is active.
The segment tables of the internal Wintherm programmer are not saved in the device. On a cycle of two seconds a momentary setpoint is calculated in each case and transmitted to the device. With the change of a segment a new pump level is also transmitted if the device supports this function and the value is not equal to zero.
If a tolerance is specified positive value not equal to zero , then before the transmission of a new setpoint, the tolerance band is checked and the setpoint output or the reaching of the tolerance band is awaited. For all the devices mentioned above, the Wintherm programmer mode always uses starting values and segment settings for temperature, tolerance and pump level. The maximum permissible values for duration and tolerance are only restricted by Wintherm itself.
The temperatures and pump levels used are device-dependent. Consequently, neither Integral T nor Variocool have adjustable pump levels. Values in this case are ignored by these devices and are not transmitted. If a device has adjustable pump levels, then the maximum values must fit in the segment table for the device Proline , all others.
Properties of the Wintherm programmer Software Programs Segments Maximum duration of a segment minutes Segment table Starting values Wintherm any number h min temperature, duration, tolerance, pump level temperature, tolerance, pump level Starting values with the Wintherm programmer The Wintherm programmer always uses starting values for the temperature, tolerance and pump level. The pump level is only used if the device supports the function. The maximum stated pump level must be suitable for the device series with ECO, Proline and Integral XT , otherwise ; the value 0 signifies that the setting is retained.
The following sections apply both to the device programmer operation and to the Wintherm programmer operation. Before starting the programmer all that needs to be determined is whether the device programmer or the Wintherm programmer is to be used. If a cell is selected, the value can be edited after clicking the same cell again or pressing the [Enter] key.
Alternatively, entry can be started immediately in the selected cell. Pressing the [Enter] key, one of the cursor keys [Up], [Down], [Left], [Right] or the [Tabulator] key terminates the entry and accepts the value. Using the cursor keys and the [Tabulator] key you can also navigate between the cells in the table directly during the entry. Lines are marked in that the line is clicked to the far left in the first column. A further click cancels the marking of a line.
If the [Ctrl] key is pressed at the same time, any other lines can be marked and if the [Shift] key is pressed simultaneously, the complete range between the first and last marked line is marked. Clicking any line within the table cancels all markings. Inserting or deleting lines occurs after marking the lines by clicking the relevant buttons Insert line or Delete line or by using the menu items with the same names in the popup menu which appears on pressing the right mouse key.
On deletion, all marked lines are deleted and on insertion as many blank lines are inserted at the position of the first marked line as were previously marked.
The Undo button restores the status before the last action. The starting values are located in the top line of the table. If the table is transmitted to a device which does not support any or not all starting values, the corresponding values or the complete line are ignored.
In this case the cells may also be blank. If the table is to be used for the Wintherm programmer, at least one valid temperature starting value must be entered. A starting value for the tolerance is practicable, but not mandatory. If the field is blank or equal to "0", the starting values are however skipped. Load from file. Loads a segment table saved in the PC for display or for editing.
Saves the currently displayed segment table under its established name. Save as Saves the currently displayed segment table under a new name and uses this name during later editing. Saves the name of the currently displayed segment table for further use with the internal Wintherm programmer. With the entry of the table for the Wintherm programmer mode a check is made for permissible values for the device currently connected and for impermissibly blank fields. A valid starting value for the temperature must be entered.
Read from device Recalls the segment table data from the device for display or for editing. With devices which manage a number of programs the program number must also be stated. Note: With the P-controller no segments nor the starting value can be read from the device. Before the table is transmitted, a check is made for permissible values for the device currently connected and for impermissibly blank fields.
A valid starting value for the temperature must only be entered if the device itself supports the use of starting values.
Insert line. Inserts a new line at the marked position. If a number of lines are marked, as many blank lines are inserted at the position of the first marked line as were previously marked. Undo negates the insertion.
Delete line. Deletes a line at the marked position. If a number of lines have been marked, all marked lines are deleted. Undo The last respective action deletion or insertion of lines is reversed. Be careful. This function clears the complete, displayed table not however the associated file from which the table was loaded. If the table has not been saved, it is also impossible to restore it. Preview of the segment table Fig.
The segment table data, the increases and the general progression of the ramps can then be checked more quickly than by a line-by-line comparison of values. The segment preview always shows the progression of the temperature over the complete cycle time.
Valid temperature segments are shown in green. Provided the table also contains entries for the tolerance and pump level, they are also displayed. Valid tolerance segments are shown in yellow and valid segments for the pump level in blue. The starting values are in each case shown in gray to the left of the value 0 on the time axis approx. Blank fields in the table are always displayed in red. The preview window is closed again by clicking the close button Create or edit segments tab On the Create or edit segments tab there are functions for editing the segment table, for loading segment tables from a file or for saving in a file as well as for transferring segments to a device or loading segments from a device.
The two other columns Tolerance and Pump level in the right half of the table can be rendered visible with the scroll bar below the table or with the cursor keys. When reading or transmitting segment tables, the corresponding program number must be selected first. If you select Read single segment you must specify the required program number and the number of the segment.
If you click on Read the corresponding segment will be read and the setpoint and the duration will be displayed. If you select Read all segments, all segments of all segment tables in the case of several programs stored in the device are read and shown in the list. The lines beginning with "0:" are each starting values. If a device does not supply any starting values, the line numbering by contrast begins with "1:". To start the transmission click on the button Read ; the transmission may take several seconds depending on the amount of data and the transmission rate.
Before starting the programmer mode, the required function must be defined by the selection of Device programmer or Wintherm programmer. For the Wintherm mode the programmer file used is shown. The desired number of cycles must be chosen and entered on starting the programmer. Wintherm programmer Wintherm uses the segment table entered as the programmer file for the calculation and transmission of new setpoints to the device.
Changed setpoints are updated on a two-second cycle. The number of the current cycle and current segment are administered by the program and are each displayed again only after the Refresh button is clicked. Device programmer The device automatically processes the saved segment table. The number of the current cycle and current segment are administered by the device and are each read again and displayed only after the Refresh button is clicked. Current programmer file During the internal Wintherm programmer mode the data are always taken from a file saved in the PC.
The file name is displayed or can be redefined here before starting the programmer mode. If Wintherm programmer is selected, the software itself starts with the calculation and cyclical output of setpoints to the device. Changes of setpoint are transmitted to the device on a two-second cycle until the termination of the programmer mode or until held with Pause.
If Device programmer is selected, Wintherm only transmits a command to the device to start the device programmer. The device then processes the saved segment table autonomously.
If Wintherm programmer is selected, the software freezes the recalculation and cyclical output of setpoints to the device until the status terminates due to a renewed Start or Stop or operation continues via Continue. If Device programmer is selected, Wintherm only transmits a command to the device to freeze the device programmer.
If Wintherm programmer is selected, the software terminates the recalculation and cyclical output of setpoints to the device. If Device programmer is selected, Wintherm only transmits a command to the device to terminate the device programmer. The device then remains in each case with the last updated setpoint.
After the start the window alters its appearance and indicates that the programmer is active. The program number, the current cycle, the current segment and the values of this segment are displayed for the running program if available as information with the device used. Click on the button Refresh to read in the current status. To terminate the acquisition for a single device proceed in the same way.
The devices involved in the acquisition are marked with a green, filled triangle in the device bar here, for example, "Therm12".
Alternatively, you can also start or stop the acquisition for all devices connected at the same time. To do this, in the menu group Start the menu items Start all devices ready for service and Stop All running devices or the corresponding symbols in the tool bar.
To check readiness for service of all devices you can perform a test run. During the test run, no data are saved. If you select the menu item Start Time control, a window will open. Here you can adjust the acquisition cycle for the devices. You can adjust the time in a range from 2 seconds to seconds 10 minutes. You can determine the measuring channels involved in the acquisition via Extended device control Settings Acquisition channels.
Error handling during the acquisition If a device signals an error, the original error messages e. On starting the acquisition a measurement file is automatically created under the uniquely issued device name, the date and an incremental number e.
After activating the acquisition, different values depending on the device function and the activated acquisition channels are read cyclically by the devices involved and written in a file as a table. The values measured by all devices include the bath temperature and the setpoint. Values measured by certain devices include up to two further external sensor temperatures, the pump pressure or the current pump and cooling power levels. In addition to the measurements the table also contains columns for the serial number "Index" , a date and time stamp in ISO format "Timestamp" and an error word "Errstate".
The error word will be " " or simply "0" if no error has occurred, otherwise you will see a number representing the error arising on the corresponding measuring channel. The numbers include both the statuses reported by the device as well as communication errors and are largely identical to the relevant error codes quoted in the LAUDA operating instructions e.
The first character of an error message is always "1". For all messages relating to channels e. If the relevant measuring cycle is entirely affected e. The characters contain information on the following channels: Measuring cycle an error has occurred generally Setpoint Bath temperature Ext. Sensor 1 34 Wintherm Plus. The axis legends for the temperatures are located at the left margin and the axis legends for the times at the bottom margin.
Operating elements for quickly changing the axis scaling are provided in the diagram to the left of the temperature axis and below the time axis. In this case the corresponding automatic axis scaling is switched off. The changes always occur in the step width of the current grid line pitch. If only one series of measurements is present, it is shown extended over a time period of one second otherwise the diagram would appear empty, since a single point is not perceptible.
Within the diagram the right and left mouse keys can be used to change the image detail. In the case of the 2D representation you can change the width of the lines. The table always has the same layout. The arrangement and number of the table columns is the same for all devices, regardless of whether a device supplies certain measurements or not. The first columns Index and Timestamp and the last column Errstate are always used.
The other columns may contain values depending on the device connected and the acquisition channels selected. Columns for which the connected device cannot supply values e. Ext1Temp, Ext2Temp in the case of a device without external sensor or which were not set up as acquisition channels will be empty Editing functions When displaying the diagram a range of editing functions are available from the menu or directly by dragging with the mouse.
Functions from the menu or the tool bar You can use them either via the menu group Diagram in the main menu or by using the tool bar in the header of the relevant diagram.
The editing functions are available both for editing archived data previous measuring value files and for editing the diagrams displayed online during the acquisition. With diagrams displayed online the option Refresh is however also switched on. The diagram is then supplemented with the latest data in time with the acquisition interval. With a diagram displayed online this option is always automatically activated as long as no extracts are displayed or automatic refresh has been switched off for the end of the time axis.
If refresh has been switched off automatically due to this type of action, it can only be reactivated by switching the zoom function on or off. Automatic refresh This option is not available with the display of an already archived diagram. With a diagram displayed online however the newest value is always appended at the end of the time axis.
Automatic refresh can be switched off if this is not desired. On the other hand, enlarging the diagram detail always switches off automatic refresh. If automatic refresh is again required, the option can be reactivated by clicking it again.
Fixed time axis This option has the effect that always only one time section of the last measurement series, defined to a certain period, is displayed.
If this time period is exceeded, then older measurement series move to the left out of the diagram, whereas the new measurement series are appended to the right. The displayed time section remains stationary, fixed to the once-only defined value. The time section can be changed under the point Manual graphic settings.
The option can be deactivated by clicking it again. The automatic time-axis setting can then be reactivated after a confirmation query. Show diagram This option only displays the diagram with values and axis legends already entered. Show diagram and table This option displays the diagram in the upper section and simultaneously the table in the lower third section.
Show table This option only displays the table with values and axis legends already entered. Zoom to original size The diagram display is reset to its initial values.
The automatic axis scaling is switched on. The diagram display is enlarged to approximately percent of its previous size. The automatic axis scaling is switched off. Zoom -. The diagram display is reduced to approximately 90 percent of its previous size. If consequently the scalings of the original display are undercut, further reduction is not carried out.
The subdivision of the grid lines ticks can be varied and the line width in the 2D display can be set within the limits of one to ten pixels. If the display is selected with a fixed time axis, the maximum time period displayed in the diagram is defined here.
Horizontal grid lines. The horizontal grid lines are superimposed or masked out. Vertical grid lines The vertical grid lines are superimposed or masked out. The legend description of the signal curves on the right diagram margin is superimposed or masked out.
This function starts the printout of the currently displayed diagram detail. Here a choice of various options can be made. In the opened window, enter all known values in order to reduce the time required for the detection. For example, if you have selected Control head E, the following window will be opened: Enter a designation of your choice must be unambiguous, however for the device in the field Device name. Specifying the device name is obligatory, it is used by the software for identifying the device unambiguously.
If you have registered the device via the automatic detection, all other settings have already been made, you can close the window directly by clicking on "Accept".
Otherwise, select the interface to which the device is connected Com Com 8 and adjust the transmission rate baud rate such that it is identical to the device setup. If you use a device with addressing, activate the option "RS" and adjust the address such that it corresponds to the device setup. Click on "Accept". For information on option "Check identity" and the fields "Ident-Message", "Model" and serial number "Serial no. They are not important for first commissioning.
As soon as a device is set up, the device symbol and the device name you have specified are displayed on the left side of the user interface in the device bar. After setting up a new device or changing the device setup, you will be requested automatically to save the new settings. Menu bar: Menu bar Tool bar Device bar Popup menu The menu bar contains different groups of the program menu.
Click on a group to open the corresponding menu group. Here, you have further selection options. Tool bar: In the tool bar you will find symbols for frequently required functions. Click on the function to have it performed directly, without having to select it via the menu bar. Device bar: The device bar contains the images of all devices registered in the software. Click on an image to establish the connection to the corresponding device. Right-click in the image to open a popup menu containing further menu items for defining or on the operation of the device.
Popup menu: Via the popup menu you can choose among several functions for quicker access to the definitions or the operation of the corresponding device. In the following you will find a short description of the function of the individual menu items: 3.
The new name is then used as the standard file Connect new device Adds a new device to the device group Properties Used for checking the interfaces available in the system and for defining the language and the number format Application information Contains all information on the devices currently contained in the device groups for viewing or printout Print Used for printing the diagram of measured values or the corresponding table Quit Used for closing the program 3.
Arrange Arranges the windows in the order they were created Overlapping Stacks the windows one above the other with an offset Vertical Used for arranging the windows vertically more lines than columns Horizontal Used for arranging the windows horizontally more columns than lines Minimize all Used for reducing the size of the windows to symbol size Close all Closes all embedded windows 3.
All actions affecting the operation of a device are started by clicking or right-clicking on the corresponding device symbol in the device bar. If you right-click on a device symbol, a popup menu will open containing a list of available actions, if you click on the symbol with the left mouse button, the software will try to establish a connection to the device. Basic device settings Opens a window where you can change the basic device settings. Remove device Removes the selected device from the device list after you have confirmed that you really want to remove the device Connect new device Opens a window where you can set up a new device.
Quit Used for closing the popup immediately. If the attempt fails, an error message will be displayed. If the connection is successful, a green arrow appears in the device bar above the image of the corresponding device. You can change frequently used device settings directly. In the simple representation, only the most important information and setting options for the most frequent functions are displayed.
The window shows the general device status OK or error , the operating status, the control and keyboard status, current measuring values and the current set value as well as the current pump output step and cooling stages if available with the device.
Here, you can change the set value and the pump output step and cooling stage and transmit them to the device by clicking on "Accept". If you click on "update", the software will read in all values from the device and update the displayed values. Click on "Diagram" to load the current file or the file last recorded with the device.
Click on "Accept" to transmit your changes to the device, read in new values and update the displayed values. The left side of the window looks the same as the window described above, on the right side you will find additional functions. Switch-over between different functional groups is effected via the buttons "Device Status", "Programmer" and "Settings". The individual device series supply different status messages. For a list of all messages refer to the Appendix. Button "Remarks" When the button "Remarks" is pressed, an editor within the program opens in which you can record comments about the description of an application or automatically add current device or program parameters see 6.
Wintherm Editor. Another device series with contact output is the series Integral control unit T The status of the contact inputs and outputs is transferred from the device and displayed here. For example, if acquisition of the set value or the pump pressure is not required, you can deactivate the corresponding entries. This saves considerable time when reading a measuring cycle, which makes sense, for example, if a large number of devices is to be acquired at the same time.
The set value and the bath temperature can be measured with all devices. One channel at least must always be marked for acquisition. The set value and bath temperatures can be represented graphically, the pump pressure or pump output step and cooling performance values are only listed in the table of measuring values. With most devices, the control parameters for proportional band xp or hold time Tn and the set-up time Tv can be changed within a certain range.
With some devices, different parameter sets are available for internal or external control. The current settings are displayed and can be changed. Click on the button "Save device temperature settings" to transmit the changed values to the device. With some devices the minimum and maximum outflow temperature can be adjusted, too, in combination with the external control system.
The safety switch-off values cannot be changed for operational safety reasons, they can only be displayed. Adjustment of the safety switch-off temperatures must always be effected at the device directly.
The outflow temperature values if used by the device can be read, edited and transmitted to the device again. Click on the button "Accept" in the main window to transmit the changed values to the device. Wintherm supports two programmer operating modes: - the programmer function if present integrated in the device and - an internal Wintherm programmer for all devices. Device programmer Most devices have an integrated programmer function in which the temporal sequence for generating a ramp is defined by segments, each consisting of the target temperature and the segment duration.
The number of segments available differs with the device series. With some device series the segment tables can be additionally spread over up to five alternatively executable programs. The segment tables are each saved in the device and are also retained after switching off.
The segment tables can be entered into the device manually or transferred to the device by Wintherm. Vice versa, existing segment tables can be read out and saved as files except that segment tables cannot be read out with P-controllers. Temperature starting value Devices in the series P-controllers and Proline use a temperature starting value, which is preset as the set value at the start of the programmer mode, in conjunction with the integrated programmer. This value is saved in the device.
Other devices do not use any starting value so that the required starting set value should be specified for the device at the start of the programmer mode in order to start from a defined initial point. Whereas the device programmer runs autonomously, the internal Wintherm programmer can only be executed when Wintherm is active.
On a cycle of two seconds a momentary set value is calculated in each case and transmitted to the device. With the change of a segment a new pump step is also transmitted if the device supports this function and the value is not equal to zero. If a tolerance is specified positive value not equal to zero , then before the transmission of a new set value, the tolerance band is checked and the set value output or the reaching of the tolerance band is awaited.
For devices in the WK class, the internal programmer function also cannot be used, because these devices are designed for continuous operation at fixed set temperatures and only allow twenty set value inputs per hour. Starting values with the Wintherm programmer The Wintherm programmer always uses starting values for the temperature, tolerance and pump step.
The pump step is only used if the device supports the function. The maximum specified pump step must be appropriate to the device series with Proline Before starting the programmer mode, the required function must be defined by the selection of "Device programmer" or "Wintherm programmer".
The two other columns "Tolerance" and "Pump step" in the right half of the table can be rendered visible with the scroll bar below the table or with the cursor keys. When reading or transmitting segment tables, the corresponding program number must be selected first. Use the arrow keys and the tab key to move the cursor in the table to the required position. Click on "Undo" to restore a line you have deleted unintentionally. Pressing the Enter key, one of the cursor keys "Up", "Down", "Left", "Right" or the tabulator key terminates the entry and accepts the value.
Clicking any line within the table cancels all markings. A further click cancels the marking of a line. If the "Ctrl" key is press at the same time, any other lines can be marked and if the "Shift" key is pressed simultaneously, the complete range between the first and last marked line is marked.
On deletion, all marked lines are deleted and on insertion as many blank lines are inserted at the position of the first marked line as were previously marked. The starting values are located in the top line of the table. In this case the cells may also be blank. If the table is to be used for the Wintherm programmer, at least one valid temperature starting value must be entered. If the field is blank or equal to "0", the starting values are however skipped.
The meaning of the buttons at the right side of the window is: Starting value With devices which support a starting value input P-controllers, Proline the starting value is displayed with Pcontrollers the starting value cannot be read. Load from file Loads a segment table saved in the PC for display or for editing. Save Saves the currently displayed segment table under its established name. Save as With the entry of the table for the Wintherm programmer mode a check is made for permissible values for the device currently connected and for impermissibly blank fields.
A valid starting value for the temperature must be entered. With devices which manage a number of programs the program number must also be stated. Before the table is transmitted, a check is made for permissible values for the device currently connected and for impermissibly blank fields.
A valid starting value for the temperature must only be entered if the device itself supports the use of starting values. Insert line Inserts a new line at the marked position.
If a number of lines are marked, as many blank lines are inserted at the position of the first marked line as were previously marked. Delete line Deletes a line at the marked position.
Undo The last respective action deletion or insertion of lines is reversed. This clears the complete, displayed table not however the associated file from which the table was loaded.
If the table has not been saved, it is also impossible to restore it. Preview Graphically displays the progression of the programmer function defined by the segment table.
The segment table data, the increases and the general progression of the ramps can then be checked more quickly than by a line-byline comparison of values. Valid temperature segments are shown in green. Valid tolerance segments are shown in yellow and valid segments for the pump step in blue.
Blank fields are always displayed in red. The preview window is closed again by clicking the close button. If you click on "Read" the corresponding segment will be read and the set value and the duration will be displayed.
If you select "Read all segments", all segments of all segment tables in the case of several programs stored in the device are read and shown in the list. The lines beginning with "0:" are each starting values.
If a device does not supply any starting values, the line numbering by contrast begins with "1:". To start the transmission click on the button "Read", the transmission may take several seconds depending on the amount of data and the transmission rate. For the programmer mode, alternatively the device programmer function if present or the internal Wintherm programmer can be used. The program number, the current cycle, the current segment and the values of this segment are displayed for the running program if available as information with the device used.
Click on the button "Update" to read in the current status. Wintherm programmer Wintherm uses the segment table entered as the programmer file for the calculation and transmission of new set values to the device. The number of the current cycle and current segment are administered by the program and are each displayed again only after the "Update" button is clicked. Device programmer The device automatically processes the saved segment table.
The number of the current cycle and current segment are administered by the device and are each read again and displayed only after the "Update" button is clicked. Current program file During the internal Wintherm programmer mode the data are always taken from a file saved in the PC. The file name is displayed or can be redefined here before starting the programmer mode. Start If "Wintherm programmer" is selected, the software itself starts with the calculation and cyclical output of set values to the device.
Changes of set value are transmitted to the device on a two-second cycle until the termination of the programmer mode or until held with "Pause". If "Device programmer" is selected, Wintherm only transmits a command to the device to start the device programmer. The device then processes the saved segment table autonomously.
If "Device programmer" is selected, Wintherm only transmits a command to the device to freeze the device programmer. Stop The device remains at the last updated set value until the status "Pause" is terminated by a renewed "Start" or "Stop" or operation is continued via "Continue".
If "Wintherm programmer" is selected, the software terminates the recalculation and cyclical output of set values to the device. If "Device programmer" is selected, Wintherm only transmits a command to the device to terminate the device programmer. The device then remains in each case with the last updated set value. The device enables the autonomous recording of measurement data during operation.
These data are the set value, bath temperature and, where present, the external temperature. The graphics memory holds recordings up to a maximum of almost lines; this amount varies according to the chosen recording method once-only or circulating recording and the recording duration. For reading out the graphics memory there are two variants, normal and fast reading.
Normal reading is mainly intended for the case in which the PC is not successful with the fast reading or if, with Wintherm, acquisition tasks running in the background should not be interrupted. In contrast, fast reading reads the data in a fraction of the time at baud approx. The time saved is however enormous. The overview must be first opened before all further actions are executed. Normal reading Starts normal reading of the recorded data.
Further operation of acquisition tasks or the Wintherm programmer mode in conjunction with slight temporal restrictions is still possible in the background. Fast reading Starts fast reading of the recorded data. Acquisition tasks running in the background or the Wintherm programmer mode are stopped while reading is taking place. The time saved is enormous. Save Saves the read-in data in a measurement file, compatible with other measurement files generated by the system.
Show graphics If the data have already been saved, the associated diagram is displayed. If the data have not yet been saved, a request is made to save the data. Change date Proline supplies the day of the month and the time at which the last recording was started.
If you would like to change the start date calculated from this or the time before saving, all data records to be saved are given new date values. Interfaces used for other purposes mouse, modem are excluded automatically. You can repeat the procedure at any time e. The interfaces which can be used are checked. If you do not want to use available interfaces for the software, simply remove the checkmark.
The language and the decimal marker can be selected independent of the language settings of your system. To take over the changes click on "Save". The changes will be active immediately and will be used as standard settings when you start the program again. To cancel the changes click on "Cancel".
The thermostat can be operated as a stand-alone device or as one of several devices at the interface of your PC. If several devices are operated at the same interface as a group, you must select RS mode. In this mode, each device is identified via a device address. For this operating mode the devices must be connected via a RSRS interface converter.
The transmission rate baud rate of all devices used must be the same, the device addresses, however, must be different.
For RS mode you only need an appropriate connecting cable, for RS mode you must connect an interface converter additionally. However, if a device is connected, the settings of the device can be checked immediately. If you use the automatic detection, however, the device must always be connected and ready for operation.
If the connection was established successfully, the window for controlling the device with current values is displayed. Otherwise, an error message will be displayed. For practical reasons, the number of connections is limited to 12 devices.
You can choose any name for the file. The application last saved becomes the standard application and will be loaded automatically when the software is started.
Click on the required image to select a device series. To allow automatic search for a device, the new device must be connected by means of a suitable cable and switched on. To reduce the time required for the detection enter all known parameters: In "Connected to:" the number of the interface e.
Check RS or RS If, in the case of RS operation, the address of the connected device is known, enter the address adjusted at the device. The program will search for all suitable interfaces available. The search for a device with completely unknown parameters may take up to 3. If a device was found that replies to the request, the search is stopped and the settings found are taken over for the device set-up. Specifying the device name is mandatory, it is used by the software for identifying the device unambiguously.
Com 8 and adjust the transmission rate baud rate such that it is identical to the device settings. If you use a device with addressing, activate the option "RS" and adjust the address such that it corresponds to the device settings.
If you want to check the identity message of the device during future connections to the device, enter the expected Ident-Message and activate the option "Check identity". If the Ident-Message is unknown leave the field empty and deactivate the option "Check identity" only. You will be asked if the Ident- Message is to be taken over in the device set-up permanently or if you want to dismiss the option. However, they are useful for better assignment in case several devices are connected.
If you have selected an invalid device series, you can return to the device selection menu "Connect new device" by clicking on the device symbol. Activating "Demo" enables a simulation mode, without a device having to be connected. Pre-settings: The first interface currently available is suggested for the connection of a new device here Com If you want to connect the device to another interface, click on one of the options offered in the list "Com: ".
Com x can use another transmission rate baud rate for communication. The baud rate settings must be identical to the baud rate of the thermostat connected to the selected interface. To adjust or check the baud rate of the thermostat, please follow the instructions of the relevant LAUDA operating instructions. If only one device is connected to the interface, the non-addressed standard RS mode is normally used for communication.
If an external RSRS interface converter is used, you can connect several devices to the same interface at the same time. In this operating mode an unambiguous device address is used for identification for each device. To set up RS mode and the device address at the thermostat, please follow the instructions of the relevant LAUDA operating instructions. To terminate the acquisition for a single device proceed in the same way. The devices involved in the acquisition are marked with a green, filled triangle in the task bar.
To start or stop the acquisition for all devices connected at the same time, use the menu items in menu group "Start" "Start all devices ready for service and "Stop all running devices or the corresponding symbols in the tool bar. During the test run, no data are saved.
The current values of all devices involved in the acquisition are displayed in the list view can be displayed and hidden. In the list, you will find the name of the corresponding device, the interface and device address if used and the measuring values read. The list is updated in each measuring cycle.
Here you can adjust the acquisition cycle for the devices. See also at chapter 3. The name of the file corresponds to the specified device name. After activating the acquisition, different values depending on the device function and the activated acquisition channels are read cyclically by the thermostats involved and written in a file as a table.
The values measured by all thermostats include the bath temperature and the set value. Values measured by certain devices include up to two further external sensor temperatures, the pump pressure or the current pump and cooling performance stage. In addition to the measuring values the table also contains columns for the serial number "Index" , the seconds elapsed since the start of the acquisition "Elapsed" , a date and time stamp in ISO format "Timestamp" and an error word "Errstate".
The error word will be "" or simply "0" if no error has occurred, otherwise you will see a number representing the error occurred at the corresponding measuring channel. The numbers include both statuses signaled by the device and communication errors. They are not identical to the error codes mentioned in the LAUDA operating instruction on the device.
The first character will always be "0" for all messages affecting a few channels only e. It is not "0" in the case of messages affecting the corresponding measuring cycle as a whole e.
These can be used for changing the layout, entering benchmark values for the representation and for exporting data or graphics from the measuring value tables. The axis legends for the temperatures are located at the left margin and the axis legends for the times at the bottom margin.
Operating elements for quickly changing the axis scaling are provided in the diagram to the left of the temperature axis and below the time axis. In this case the corresponding automatic axis scaling is switched off. In order that the diagram can also be practicably displayed with only one measurement series available, the very first measurement series is displayed extended over a time period of 1 s otherwise the diagram would appear blank, because a single point cannot be discerned.
Within the diagram the right and left mouse keys can be used to change the image detail. In the case of the 2D representation you can change the width of the lines. The arrangement and number of the table columns is the same for all devices, regardless of whether a device supplies certain values or not. The first columns Index and Timestamp and the last column Errstate are always used.
The other columns may contain values depending on the device connected and the acquisition channels selected. Ext1Temp, Ext2Temp in the case of a device without external sensor or which were not set up as acquisition channels will be empty. The menu group uses the same symbols as the tool bar.
The menu group additionally supports the functions "Copy", Save As The editing functions are available both for editing archived data previous measuring value files and for editing the diagrams displayed online during the acquisition. In the case of the online diagrams you can also activate the "Update" option. In this case, the diagram data are updated periodically depending on the acquisition interval adjusted.
The "Update" option is automatically switched off in most cases of zoom actions. To activate the "Update" option again, reset zoom to original size or simply reactivate this option. Automatic update This option is not available with the display of an already archived diagram.
With a diagram displayed online however the newest value is always appended at the end of the time axis. Automatic updating can be switched off if this is not desired. If automatic updating is again required, the option can be reactivated by clicking it again. Fixed time axis The option "Fixed time axis" has the effect that always only one time section of the last measurement series, defined to a certain period, is displayed.
If this time period is exceeded, then older measurement series move to the left out of the diagram, whereas the new measurement series are appended to the right. The displayed time section remains stationary, fixed to the once-only defined value. The time section can be changed under the point " Manual entries". The automatic time-axis setting can then be reactivated after a confirmation query. Display diagram Displays only the diagram with values and axis legends already entered.
Display diagram and table Displays the diagram in the upper section and simultaneously the table in the lower third section. Display table Displays only the table with the values already entered. In addition to the zoom functions in the tool bar, there is another useful method to zoom in or out certain areas of the diagram. To restore the original size, proceed in opposite order click on lower right corner and drag mouse pointer to the left and upward.
Click on the upper left corner of the area you want to zoom in and drag the mouse to the right and downward. If you release the mouse button, the selected area is zoomed in. Manual entries The minima and maxima of the temperature and time axes can be changed to any values using manual entries. The subdivision of the gridlines ticks can be varied and the line width in the 2D display can be set within the limits of one to ten pixels.
If the display is selected with a fixed time axis, the maximum time period displayed in the diagram is defined here. View in 3D The normal 2D line display is changed to a 3D display and vice versa. Horizontal gridlines The horizontal gridlines are superimposed or masked out. Vertical gridlines The vertical gridlines are superimposed or masked out. Legend The legend description of the signal curves on the right diagram margin is superimposed or masked out. Print "Print" starts the printout of the currently displayed diagram detail.
Just the diagram or the table values can be printed out or both together. Enlarging a diagram detail If, with the left mouse key held down, the mouse pointer is dragged from the top left to the bottom right, the diagram is enlarged on this section when the mouse key is released with the 3D view the mouse pointer must be located within the axis scalings on the front plane, otherwise there is no reaction.
Resetting the diagram detail If the mouse pointer is dragged from the bottom right to the top left with the left mouse key held down, i. In this respect the start position at which the right mouse key is pressed determines which action occurs.
The automatic axis scaling for the affected axes is switched off. The various possibilities can be selected as options. Print diagram and data records The diagram is printed on the first page of the printout, followed by the table with the measurement series. Print diagram only Only the diagram is printed. Print data records only Only the measurement series are printed.
Use screen display If the printout of the diagram is selected above, the layout can be as implemented on the screen diagram as screen copy or presented as a drawing. With a printout as a drawing, a white background is always selected and the diagram is "drawn on paper" anew. This makes it possible to track the temperature-controlled processes in the laboratory.
Download Related Files. Visit Website. With about employees, more than EUR 60 million in annual turnover and eleven foreign subsidia Learn More. Email Address. Send Enquiry. KG website.
❿
Bangla Word Software Free Download For PC - Bangla word software free download for pc
Looking for:
Bangla word software free download for pc |
Bangla word software free download for pc
Overview Of Bangla Word Software - Bangla word software free download for pc
Download madden nfl 2001 pc.Abandonware Games / madden nfl - Madden Nfl
Looking for:
Download madden nfl 2001 pc |
Download Madden NFL 2001 (Windows) - Download madden nfl 2001 pc
Windows Server R2 ISO+Crack Full Download – Skyvroo Web. Windows server 2012 r2 download iso with crack 32 bit free
Looking for:
Windows server 2012 r2 download iso with crack 32 bit free |
Windows server 2012 r2 download iso with crack 32 bit free.Please select your Windows Server 2012 R2 download
Kitkat download for pc
Looking for:
Kitkat download for pc |
Kitkat download for pc.Download & Install Android KitKat on Windows PC, Laptops as Dual Boot
Kitkat download for pc.Latest Apps
Hello Guys.!! Also we have limited space of 2GB when we install using Android-x86 4. You can uninstall it anytime like you uninstall a Program in Windows. After installation you will got an option at boot to select Windows or Android.
See the Screenshot below. Make sure you hit the subscribe button to stay up to date with the new videos we upload every week. He spends most of his weekends working with IoT devices and playing games on the Xbox. He is also a solo-traveler who loves hiking and exploring new trails. Follow him on. TwitterFacebookand YouTube. This site uses Akismet to reduce spam. Learn how your comment data is processed. Plz Update. I have a нажмите чтобы увидеть больше notebook flex kitkat download for pc and apparently only supports UEFI, did the installation procedure then restart the system, I chose android but I had error.
Maybe you can help me. /28744.txt must download EFI image file of Android x86 4. How to disable? How to install Android 4. Contents hide. Before You Go….
What's Your Reaction? Leave a Reply Cancel reply. Reply with GIF. These permissions can be the way OS to windows 10 not? Vote Up 0 Vote Down. In which format should the sd card be? Plz Update Loading We kitkat download for pc updated it!! We notice you're using an adblocker. We've made a point of never allowing auto-playing video ads or ads that obscure content, such as pop-ups.
Please support us by whitelisting kitkat download for pc domain. Loading Comments Email Required Name Required Website.
❿Kitkat download for pc.Download & Install Android KitKat on Windows PC, Laptops as Dual Boot
Winbond w83697hf vga driver download
Looking for:
Winbond w83697hf vga driver download |
Winbond w83697hf vga driver download - 2.6.3 Winbond W83627EHG Super I/O chipset
Winbond w83697hf vga driver download
Grand prix legends pc game free download.GRAND PRIX LEGENDS
Looking for:
Grand prix legends pc game free download |
Grand prix legends pc game free download.Grand Prix Legends
Grand prix legends pc game free download
GPL is a racing simulation for the PC that was published inyes you read correctly, 22 years ago. In it simulates much more This demo shall give you the possibility to enjoy the best of GPL in a fully win 7 ultimate 32 bit iso download deutsch demo game to get a feel why it is still alive after such a long time and to get you excited about delving deeper по этому адресу the GPL universe.
The GPL Demo contains ten cars from the major mods, four tracks, all original patches, modernized graphics and latest fixes and improvements made by the GPL community, that have been created in the last 22 years.
A full GPL mod normally includes a field of cars with individual car physics and tracks to fully grand prix legends pc game free download that year of racing. This demo includes the best cars of all mods. One car was chosen from each of the nine major mods plus one additional car from the original F1 simulation to demonstrate how far we have come in 22 years. Conveniently, the driver champion in each year drove these cars with one exception.
The cars are:. The Mercedes W simulates brake fade and has a light indicator in the cockpit to show the condition grand prix legends pc game free download your brakes.
The light is not historically correct, but very helpful. If you want a normal dash without any indicator light until you push the brakes too far and get a yellow or red indicator you can use the tempfade. If you want to go back to the original brake fade light indicator, just delete the tempfade.
The grand prix legends pc game free download was to choose one track from each mod that best represented that mod year or was used for many years over several different mods. Note: Some tracks include options that you can use. Built in the Royal Villa of Monza park in a woodland setting, the site has three tracks — the 5. The high speed curve, Curva Grande, is located dlwnload the Variante del Rettifilo which is located at the end of the front straight or Rettifilo Tribune, and is usually taken flat out by Formula One cars.
The route has been frequently changed since Some chicanes have been rebuilt over the years with larger run-out zones to meet the demands of downloas motorsport. Curves that were once grand prix legends pc game free download left-right combination are now taken in reverse order. Later, however, the tyre stacks were removed again and used again only in the s, after the track had claimed many lives due to the enormous speeds.
Inthe two steep bends built in were rebuilt to be even steeper. The overall course, which was a combination of both tracks, was almost exactly grand prix legends pc game free download dowjload long and was used four times in Formula 1 races the last time was in In the meantime the steep curve combination is falling into disrepair.
Road America was designed and built by avid racing enthusiast and highway engineer Clif Tufte, whose sand and gravel company owned the land on which Road America was built. Seed financing came from members grand prix legends pc game free download the local community and regional SCCA chapters.
The construction of the track began in April The natural grand prix legends pc game free download of the Kettle Moraine area was utilized for the track, which sweeps over the tops of rolling hills and plunges down through bottom land then up the steep narrow ravine known as Thunder Grandd. The track is 4. Except for recent re-modeling work on Turn 1 that changed it very slightly, the track is the same today as when it was first laid out. Sebring International Raceway is a road course auto racing facility in the southeastern United States, grand prix legends pc game free download near Sebring, Florida.
Sebring pronounced sea-bring Raceway is one of the oldest continuously operating race tracks in doownload U. Grand prix legends pc game free download is one of the classic race tracks in North American sports car racing and plays host to the 12 Hours of Sebring. The raceway occupies a portion of Sebring Regional Airport, an active airport for private and commercial traffic that was originally built as Hendricks Army Airfield, a World War II training base for the U.
Army Air Forces. The course was held at the end of the s on the former airport grounds of the Downlkad Army Airfield and was modelled on European motorcycle racing courses. The first race took place inbut on an 8. In fujitsu siemens amilo la 1703 drivers download win 7 race took place on a shortened 7. From to the length was 7. Then the north-south runway was left out and replaced by a new piece of asphalt with the /905.txt carousel, so that the length shrank to 6.
Inthe eight and nine bends and the carousel were removed again. The length was reduced to 5. At the end ofthe /48120.txt chicane was relocated. This shortened the course to 5. In the entry and exit of the Ulmann Straight in front of the finish curve were redesigned, which extended the course to 6 kilometers.
Legfnds the end of the last rebuilding took place. The hairpin bend bend 5 was converted into an S bend. In the surface was renewed from curve 1 to curve At the end of the Formula 1 season the first Grand Prix of the USA took place here - but it was also the last time that Formula 1 was a grand prix legends pc game free download here.
Between andthe Formula 1 race track, originally almost 4. In the World Road Championships were held on the grand prix legends pc game free download. The circuit winds its way through the dunes north of Zandvoort. The original course character consists mainly of fast curves and a hairpin curve after start and finish.
Ffree film Grand Prix shows a continuous lap from the driver's perspective, shot in Since the track no longer met the safety standards after - the F1 racing driver Piers Courage had already had an accident here at the GP on 21 June and was burned in his car - it was rebuilt and only re-included in the Formula 1 calendar in A new chicane with the name Panorama had been added, but despite the new standards the British driver Roger Williamson died at the GP on 29 Julyhe also burned in his F1 car.
Another chicane was added in After the Formula 1 did not appear any more in Zandvoort. In the circuit was last rebuilt and extended to its current length of 4. In Mayit was announced that Formula 1 would return to Zandvoort from after a year interruption.
The contract is initially dated untiland the date grznd expected to be set at the beginning of the racing calendar. Characteristic is the roller coaster ride, because it is constantly over hills, but also treacherous hilltops and bumps. Also very special is the permanent dune sand, which is blown by the coastal wind on and over the roadway. This demo has the patch applied that removes the top and bottom black bars for a larger viewing area.
This demo has the patch applied that reduces Force Feedback FFB latency and removes all non-physics forces. Donwload default the core. For heavier cars, like sports cars, you may want to useor even instead of These are the freee steps for you to drive grand prix legends pc game free download GPL Demo as quickly as possible.
Or if you have downloaded the zip version, unpack the zip and start the demo by double clicking on the gpldemo. Адрес first time you start the demo, you will need to select and calibrate your controls and set your screen resolution as shown in steps 3, 4, and 5.
Click the Options button. Click the right arrow button until the Controls Menu is displayed. Tip: When you configure your wheel for the first time, it may happen that you cannot assign your Brake even grand prix legends pc game free download the demo detects it.
Then click on the Calibrate Joystick s button. The Brake Axis 1 ссылка display Unassigned, but even so you will be able to push your brake pedal and the calibration menu will show it. Go back to the Joystick Calibration menu. Click on the Calibrate Joystick s button again.
Click the green button to enter feee Track Select menu in the Training mode for practice driving. If the Training mode is not displayed, click the right arrow grand prix legends pc game free download until it is. Click the green button to enter the car and drive it. You will be in the Lotus 33 /922.txt the Road America track. GPL does not run in a normal PC window so follow these steps to exit the demo: Click the red button, OK button, red button, red button, then any key.
This demo comes preloaded with a demo driver profile GPL Demo You can create a new player with your name by going to the main menu Player Info and click the New button. The demo initially starts with the OpenGLv2 rasterizer for the 3D accelerator. You have to test what works best on your system. Just copy the app. If you want to go back to the other gme just copy the other app. The GPL Demo comes already with optimized graphics settings in the core.
But you can improve the graphics inside your graphics card driver menu. The Antialiasing Supersampling is e. For example for the GPL F1 mod you would need to create a жмите for the gplc Please scroll further down for the settings for an AMD Radeon graphics card.
But do a quick test race with a full grid after each value you have changed to see if GPL still runs smoothly with full 36 FPS frames per second. Click on the button Export user defined profiles and choose the option Export all driver profiles. These settings can cause frame rate drops /7421.txt weaker PC systems.
You legnds to patch your gpldemo. These are grwnd grand prix legends pc game free download. In each case the final digit in the extension will designate the car class, with 1 being Grand Prix, 2 being the Dpwnload Trainer, and 3 being the Novice Trainer.
Thus a setup for the GP Lotus 49 legendw have the extension.
❿Grand prix legends pc game free download.Game Description
Video Audio icon An illustration of an audio speaker. Audio Software icon An illustration of a 3. Software Images icon An illustration of two photographs. Images Donate icon An illustration of a heart shape Donate Ellipses icon An illustration of text ellipses. Metropolitan Museum Cleveland Museum of Art.
Internet Arcade Console Living Room. Books to Borrow Open Library. Search the Wayback Machine Search icon An illustration of a magnifying glass.
Sign up for free Log in. EMBED for wordpress. Want more? Advanced embedding details, examples, and help! Publication date Usage Public Domain Mark 1. Platform PC. Yes, simulator, like Richard Burns Rally.
Very, very difficult, very realistic and demanding game. Similar games Users also downloaded the following old games. Stronghold Strategic Simulations. Railroad Tycoon 3 Gathering of Developers. The Punisher THQ. Thief: Deadly Shadows Eidos. Aces over Europe Sierra On-Line. Latest added games View All. Top rated games View All. The games you can find on our pages are no longer supported by the publishers.
You will not buy them in stores anymore. The aim of abandonwaregames. All the games you can download for free and play on modern computers. On AbandonwareGames. We respect the applicable copyright. All reported or unsuitable titles will be removed from our sites.
❿
Subscribe to:
Posts (Atom)
Wintherm software free download.Downloads | ThermoAnalytics
Looking for: Wintherm software free download Click here to DOWNLOAD ❿ Downloads - Analysis Tech. Wintherm software free download...
-
Looking for: Rugby 08 download pc Click here to DOWNLOAD Rugby 08 download pc File name: ; File size: MB; Mime type: applicati...
-
Looking for: Secret of mana 2 pc download Click here to DOWNLOAD Secret of mana 2 pc download.Secret of Mana Мы не в восхищени...
-
Looking for: Download microsoft security essentials for windows 10 free Click here to DOWNLOAD Lightweight malware protection - Do...
